Cumbria · England
Bath re-enamelling & resurfacing in Marton, Cumbria
Bath re-enamelling in Marton without the cost of replacing. Get a fixed quote from your photos, then we come to you.
- Resurfacing from £350
- A bath that stays dull however much you clean it
- An outdated colour you’d like to change
Covering Marton
Marton is about 3 miles west of Ulverston, in Cumbria. From the centre of Marton to the outlying streets, we offer exactly the same service: a fixed price, a tidy visit and a guarantee. We work in all 438 towns and villages in Cumbria. We work right across the region, from Marton to Liverpool (54 miles away).
Our visits in LA12 work the same way as everywhere else we cover. Close by, we cover Lindal in Furness (1 mile south-east), Ireleth (1 mile west), Pennington (1 mile east), Paradise (1 mile north-west) and Dalton-in-Furness (2 miles south). Within a short drive, we also cover Barrow-in-Furness (5 miles south-west), Ulverston (3 miles east), Hindpool (5 miles south-west), Salthouse (5 miles south), Risedale (5 miles south) and Vickerstown (6 miles south-west).
Around Marton
Our clients here include homes close to Church of St Peter, Dowdales School and Lindal and Marton Primary School and the streets around them. For rail, the closest station is Askam station, roughly 1.7 miles west of the centre. Other landmarks nearby include Furness General Hospital (3.6 miles south-west) and Laurel And Hardy Museum (3 miles east). For a walk, there is High Moor and Urswick Tarn.
Bath re-enamelling at your home in Marton
If your bath is sound but looks tired, resurfacing is normally the best value. There is no removal, plumbing or tiling involved. If you’re dealing with staining under the taps and around the waste and chips and rust in more than one place, we can help, on acrylic baths, cast iron baths and pressed steel baths alike.
Whatever the size of the job, it’s backed by a one-year guarantee in Marton and across Cumbria.
- Where
- Marton (LA12)
- County
- Cumbria
- Warranty
- 12 months on all our work
- Price
- From £350. Fixed and free, based on photos
- Telephone
- 0345 017 0787
- Page updated
- 23 October 2026
Looking after it afterwards
Nothing complicated is needed:
- Wash away dyes and oils after use
- Wipe the bath dry after use in hard water areas
- Respect the curing time we give you
- Get any chip repaired quickly
Rinse away dyes, oils and bath bombs straight after use, as they can stain. Fix dripping taps quickly.
The longer worn enamel is left, the rougher it gets, and rust spots spread under the surface. Acting earlier keeps the preparation simpler.
Repairing versus replacing in Marton
Replacing the bath means a plumber, lifting out the old bath, re-tiling or making good the walls and several days without a working bathroom. Re-enamelling renews the whole surface without moving it. Our bath re-enamelling starts from £350. Set against the cost of replacement, a repair is usually a fraction of the price, because nothing has to be taken out, refitted or made good. Your fixed quote shows exactly what’s included.
Why us?
- Colours mixed by hand to suit your surface
- One price list for the entire UK
- Everything repaired in place
- Repair technicians who travel to you, UK-wide
See our pricing and bath cost comparison.
What bath re-enamelling costs
Resurfacing from £350. There’s no charge for travel to Marton. The price depends on:
- Access to the area
- The size and number of damaged areas
- Previous DIY repairs that have to come out
- What kind of damage it is
Rather than charging by the hour, we fix the price before we start. It depends on the damage, the material and access, and doing several items at once reduces it.
Send photos for a quote
The better the photos, the more accurate the price. Here’s what helps:
- What it’s made of, if you know
- Details of any past repairs
- Good light, ideally daylight, without flash glare
- A clear, close picture of the problem area
The quickest way to a price is to send two or three pictures using our quote form or ring us. We’ll say right away if a repair is the right fix.
Landlord and trade work in Marton
Rental properties take more wear, and replacing items every time a tenant leaves is expensive. A repair between tenancies is a cheaper way to keep the property in good order.
Builders, developers and site managers book us for snagging repairs, fixing chips and scratches before handover so nothing needs replacing. We hold CHAS, Constructionline and SafeContractor accreditations.
Signs you need bath re-enamelling in Marton
Older baths often have several problems at once: worn patches, chips, rust spots and stains. Resurfacing sorts them out together.
Most people contact us when they notice something like this:
- Several chips and rust patches
- Brown or grey marks that do not clean off
- A dull, rough surface that won’t come clean
- A bath in a colour that no longer suits
Comparing quotes
- How soon you can use it again
- The length of the guarantee and what it covers
- Who turns up on the day
- What aftercare is recommended
Your questions about bath re-enamelling in Marton
Is there a guarantee?
Every repair comes with a one-year guarantee. We’ll explain what it covers when we quote.
How long is the bath unusable?
Generally one day, with the bath ready the following day. A badly pitted bath can need a second day.
I rent my home. Can I book you?
Of course. Ask your landlord first, and we can send them the quote if that helps.
What happens once I’ve sent pictures?
You’ll get a fixed quote back. There is no obligation to book.
Does the bath have to be removed?
No, it stays where it is. Everything is done in your bathroom, with the room protected and ventilated.
Can you do the outside of a roll-top?
Yes, roll-tops are a big part of our work. We resurface the inside, and the outside can be refinished too.
Do the materials smell?
It depends on the job, but frequently a little. Ventilation keeps it to a minimum, and it soon fades.
When can you do it?
That depends on our diary for your area. Send photos with your postcode and we’ll reply with the earliest dates.
Other services in Marton
Materials and what they mean for the repair
Pressed steel
Steel baths re-enamel well, once any rust has been treated. Steel frequently rusts by the plughole, so we check it carefully.
Cast iron
A cast iron bath is heavy enough that most people never want to move it. The enamel is the part that wears or chips, and that is the part we put right.
When a repair is not the answer
To be straight with you, some problems need a different fix:
- Anything hidden under an old coating, until we remove it
- An acrylic bath that flexes badly underfoot
- A cast iron or steel bath that’s cracked right through
If in doubt, send pictures and we will say what we think before you book.
What we work on
- Cast iron baths
- Victorian roll-tops
- Pressed steel baths
- Basins & shower trays
- Acrylic baths
What happens on the day
From the moment we arrive, the aim is to do the job without disturbing the rest of your home. Surfaces nearby are masked off, the job takes a full day, and we finish with a tidy-up and a look at the finished work together.
- The bathroom is protected and ventilation set up.
- Old sealant is cut out and the bath is deep cleaned.
- Chips, rust and pitting are repaired.
- The surface is keyed and primed for the new finish.
- Several coats of finish are sprayed on, then it cures until the following day.
Preparing for the visit
- Make sure the area is dry
- Open a window if you can
- Keep a parking space free if you can
Getting a price
There is no need for us to visit first. Nearly every job can be priced from pictures: send a close-up, a wider shot and your postcode, and we’ll reply with a fixed quote.
Advice
About our accreditations · Every repair comes with a one-year guarantee.
