Norfolk · England
Bath Re-enamelling in Matlaske
Bath re-enamelling in and around Matlaske: photo quotes, tidy work and a year’s guarantee.
- Resurfacing from £350
- A peeling or bubbling previous coating
- An outdated colour you’d like to change
How the visit works
You do not need to empty the room beforehand. Everything we use comes in the van with us, lay protective sheets and start once you’re happy with the plan. It usually takes a full day, and you can get on with other things while we are there.
- We check the bath and agree the finish with you.
- Everything around the bath is masked and covered.
- The bath is degreased, repaired and keyed.
- We apply the primer and then the finish coats.
- We remove the masking, tidy up and give you the curing time.
Before we arrive
- Open a window if you can
- Clear toiletries, mats and anything else from around the area
- Tell us about any previous repairs or coatings
Getting a price
For a price in Matlaske, the easiest route is photos: one close up, one from further back, plus your postcode. We reply with a fixed quote and our next available dates.
Advice
Bath re-enamelling in Matlaske, done in place
The bath stays where it is, so your taps, tiles and plumbing are left alone. It typically takes one visit, with the bath ready to use the following day. We regularly repair cast iron baths, Victorian roll-tops and pressed steel baths, and people most often call us about wear marks under the taps and enamel that’s lost its shine and feels rough.
You are covered after we leave: our one-year guarantee applies to every job, and we explain what it covers before booking.
- Area
- Matlaske (NR11)
- Area hub
- Norfolk
- Cover
- One year on every repair
- Quote
- From £350. Free, fixed price from pictures
- Telephone
- 0345 017 0787
- Last updated
- 23 October 2026
When to call us in Matlaske
By the time a bath is a few decades old, it may have a mix of issues: dull areas, chips, rust and staining. Resurfacing sorts them out together.
Typical reasons for a call-out include:
- A bath in a colour that no longer suits
- Chips and rust in more than one place
- Worn patches where water runs and sits
- Enamel that’s lost its shine and feels rough
What to look for in a quote
- What aftercare is recommended
- How soon you can use it again
- What prep work is covered
- How the colour is matched
About Matlaske
Matlaske is about 9 miles west of North Walsham, in Norfolk. Whether you’re in the middle of Matlaske or on the outskirts, we offer exactly the same service: fixed prices, tidy work and a one-year guarantee. Matlaske is one of 797 places in Norfolk we cover.
Our visits in NR11 work the same way as everywhere else we cover. Other places close to Matlaske include Little Barningham (1 mile south-west), Plumstead (1 mile west), Baconsthorpe (2 miles north-west), Itteringham (2 miles south) and Hempstead (3 miles north-west). Larger places within reach include North Walsham (9 miles east), Sheringham (5 miles north), Taverham (13 miles south), Cromer (6 miles north-east), Fakenham (14 miles west) and Aylsham (6 miles south-east).
Around Matlaske
Our customers here include homes close to Church of St Peter. Nearby you’ll also find Bessingham Moat Yard (1.8 miles north-east). Open spaces near Matlaske include Beacon Hill.
Places near Matlaske
Also in Matlaske
Can I fix it myself?
For a hairline mark somewhere you’ll never see, a kit may be enough. For anything you look at every day, anything that has rusted, cracked or holed, or anything on a coloured surface, a professional repair is worth it.
It’s tempting to reach for a kit, but the repairs we redo most frequently are DIY ones that have discoloured or lifted. Doing it properly first is generally the cheaper route.
What affects the price in Matlaske
Resurfacing from £350. There’s no area surcharge for Matlaske. What changes the price is:
- The size and number of damaged areas
- Unusual colours or finishes
- The material
- Where the damage is and how we get to it
The price reflects the work involved, not your postcode. The full price is agreed before booking, with nothing added on the day.
Quotes from your photos
Before you send pictures, these tips help us give you a firm price:
- One picture of the entire bath
- Your postcode, so we can check dates
- Details of any past repairs
- The material, if you know it
You do not need a survey visit. Photos are enough for us to price nearly every job: we need a close-up, a wider picture and your postcode, and we’ll come back to you with a fixed figure.
What a repair cannot fix
Some problems need a builder, plumber or fitter rather than us:
- Anything hidden under an old coating, until we remove it
- Steel that has corroded right through
- A metal bath with a through crack
Not sure? Send photos and we will give you a straight answer before you book.
Materials we work on in Matlaske
- Pressed steel baths
- Victorian roll-tops
- Acrylic baths
- Basins & shower trays
- Cast iron baths
Keeping it looking good
To keep it looking its best:
- Leave the bath for the full curing time before using it
- Stick to gentle, non-abrasive cleaners
- Repair dripping taps early
- Keep toiletries on a shelf rather than in the bath
Dry the bath after use if possible, particularly with hard water, and rinse off any bath products.
Rust spots on a worn bath get worse with time and make the job bigger. It’s simpler to resurface before they spread.
Landlord and trade work in Matlaske
We’re used to working with agents and managing companies. Send the address, pictures and access details.
Rental properties take more wear, and replacing items every time a tenant leaves is expensive. A repair between tenancies is a cheaper way to keep the property in good order.
Questions from Matlaske
Will you leave a mess?
Dust sheets and masking go down before we start, and tidy up before we leave.
Are you a vetted contractor?
We hold CHAS, Constructionline, SafeContractor, SMAS Worksafe and Builder’s Profile accreditations.
Can you do more than one item on the same visit?
Yes. Combining jobs on one visit brings the cost down. Send photos of everything you’d like done.
How long does re-enamelling last?
A well-prepared finish lasts a long time if it’s looked after. Gentle cleaning, no suction mats.
Do you need to take the bath out?
No. It’s re-enamelled where it stands, so nothing else is disturbed.
Is a repair better than a new one?
In most cases, yes. Replacement brings removal, refitting and making good, which a repair avoids. If it isn’t worth repairing, we’ll tell you.
I’m a tenant. Can you help?
Yes. Ask your landlord first, and we can send them the quote if that helps.
Can a failed resurfacing be redone?
Yes, we do this regularly. Removing the old finish takes extra time, which we include in the price.
Repair or replace: which is better?
Replacing a bath normally involves a plumber, a fitter and a tiler. Resurfacing is one technician, normally in a day, and the bath can be used the day after. Prices start from £350. Our prices are the same across the UK, with no extra for Matlaske. The job itself decides the price: the material, the amount of damage and how many items.
What you get with us
- Repair technicians who travel to you, UK-wide
- We leave the room as we found it
- One visit for most repairs
- Colours mixed by hand to suit your surface
See our prices page and resurfacing vs replacement cost guide.
About our accreditations · Every repair comes with a one-year guarantee.
