Dorset · England
Bath Re-enamelling in Melcombe Bingham
Fixed-price bath re-enamelling in Melcombe Bingham and the surrounding area, normally in one visit and guaranteed for a year.
- Resurfacing from £350
- Several chips and rust patches
- A bath in a colour that no longer suits
How we handle bath re-enamelling in Melcombe Bingham
A re-enamelled bath looks and feels like a new one, but without the cost and upheaval of a refit. It suits anyone happy with the bathroom apart from the bath. We’re often asked to fix several chips and rust patches and enamel that’s lost its shine and feels rough, across Victorian roll-tops, pressed steel baths and basins & shower trays.
You get a one-year guarantee, the same in Melcombe Bingham as everywhere else we work.
- Location
- Melcombe Bingham (DT2)
- Area hub
- Dorset
- Cover
- A year, on every repair
- Price
- From £350. Free and fixed, from your pictures
- Phone
- 0345 017 0787
- Last updated
- 23 October 2026
Covering Melcombe Bingham
Melcombe Bingham is about 8 miles west of Blandford Forum, in Dorset. We travel to customers in Melcombe Bingham, so nothing has to leave your home. Our technicians cover 462 places in Dorset.
Every address in DT2 is covered, from the main roads to the quietest streets. Neighbouring places we cover include Ansty (1 mile north), Cross Lanes (1 mile south-west), Lower Ansty (1 mile north-east), Higher Ansty (1 mile north-east) and Little Ansty (1 mile north). Further out, we also cover Weymouth (15 miles south), Dorchester (9 miles south-west), Blandford Forum (8 miles east), Gillingham (15 miles north), Shaftesbury (14 miles north-east) and Sherborne (12 miles north-west).
Around Melcombe Bingham
Around Melcombe Bingham, we work in homes near Milton Abbey School and Church of St Andrew, among other places. Nearby you’ll also find Brewery Farm Museum (2.6 miles east). The countryside around Melcombe Bingham includes Lyscombe Hill.
How it works
Once we’re through the door, we keep the work contained to the one room. We mask off everything nearby, the work takes a full day, depending on what we find, and we finish by cleaning up and talking you through the result.
- We check the bath and agree the finish with you.
- Everything around the bath is masked and covered.
- The bath is degreased, repaired and keyed.
- Primer and finish coats are applied.
- We remove the masking, tidy up and give you the curing time.
Getting ready for the visit
- Let us know if it has been repaired before
- Let us know about parking or access
- Let the surface dry out before the visit
Ask for a price
A quote takes minutes to ask for: take one close-up and one wider shot of the bath, include your postcode and send them to us. What comes back is a fixed quote, not a guess.
Read more
When to call us in Melcombe Bingham
Enamel does not fail overnight. Years of cleaning, hard water and hot baths dull the surface, starting where water runs and sits.
You may need us if you’ve spotted:
- A dull, rough surface that will not come clean
- An original cast iron bath that needs restoring
- Worn patches where water runs and sits
- Brown or grey marks that don’t clean off
Questions to ask before booking
- How long it needs to cure
- If travel is included in the price
- Whether cleaning and preparation are in the price
- Whether a trained technician does the job
Places near Melcombe Bingham
Other services in Melcombe Bingham
Work for landlords and builders
For anyone letting property in or around Melcombe Bingham, we can repair and quote for several addresses together. Just send photos for each address and we will price them together.
Housing associations and facilities teams use us for planned and reactive repairs. Repairing in place avoids the disruption of a replacement, which matters when someone is living in the home.
Different materials, different repairs
Cast iron
Re-enamelling suits cast iron baths perfectly. They’re built to last, and only the surface wears, so a new finish makes them look new again.
Roll-top and period baths
We can resurface a roll-top inside and out, and the outside can be refinished too.
When we would advise against a repair
We will always be straight with you, so here’s what a repair can’t fix:
- Steel that has corroded right through
- A metal bath with a through crack
- A poorly supported acrylic bath, until it’s firmed up
If in doubt, send pictures and we will say what we think before you book.
Surfaces we repair
- Cast iron baths
- Basins & shower trays
- Acrylic baths
- Victorian roll-tops
- Pressed steel baths
Keeping it looking good
So the finish stays in good condition:
- Clean with a soft cloth and mild detergent
- Do not use the bath until it has fully cured
- Keep toiletries on a shelf rather than in the bath
- Fix dripping taps quickly
Dry the bath after use if possible, especially in hard water areas, and rinse away any product left on the surface.
Worn enamel only gets rougher with time, and any rust spreads underneath. Resurfacing sooner means less repair work first.
Common questions in Melcombe Bingham
Do you hold any accreditations?
Yes. Our accreditations include CHAS, Constructionline and SafeContractor. The full list is on our accreditations page.
Do you cover the entire of Dorset?
Everywhere in the UK, Melcombe Bingham included. There’s no extra charge for travel.
Do you come to Melcombe Bingham?
Yes. We work across the UK and travel to Melcombe Bingham and the rest of Dorset. Send us pictures for a fixed quote, or call 0345 017 0787.
How do I get a price for bath re-enamelling in Melcombe Bingham?
Resurfacing from £350. Because every job differs, we price from pictures. You know the full cost before anything is booked.
Do the materials smell?
There can be some smell while we work, so we ventilate the room. It clears as the materials cure.
Can you do more than one item on the same visit?
Yes. Doing several items on one visit usually costs less than separate visits. Include pictures of each item.
Can you change the colour of my bath?
Yes, white is the usual choice. Mention the colour you want when you send pictures.
Do you do work for letting agents?
Yes. We carry out repairs for householders, landlords, letting agents, builders and businesses.
Should I try a DIY kit first?
For a hairline mark somewhere you will never see, a kit may be enough. For anything you look at every day, anything that has rusted, cracked or holed, or anything on a coloured surface, a professional repair is worth it.
If you’ve already tried a DIY fix, that is fine. We take the old repair out and do it properly, so it does not stop a professional repair. Just mention it when you send pictures, as it can add time.
What bath re-enamelling costs
Resurfacing from £350. You will not pay by the hour. The price is based on:
- How many areas need work
- What the surface is made of
- Previous DIY repairs that have to come out
- Whether it’s a chip, crack, burn or wear
Our prices are the same across the UK, with no extra for Melcombe Bingham. The job itself decides the price: how much damage, what it’s made of and how many items.
Quotes from your photos
We price nearly every job from photos. This is what we need:
- Whether it’s been repaired or coated before
- Daylight if possible, and no flash reflection
- Where you are, by postcode
- A close-up of the damage, in focus
Email us pictures of the damage and one of the whole item, with your DT2 postcode, and we’ll reply with a fixed price.
About our accreditations · Every repair comes with a one-year guarantee.
