Shropshire · England
Bath Re-enamelling in Moreton Mill
Local bath re-enamelling for Moreton Mill: photo quotes, tidy work and a year’s guarantee.
- Resurfacing from £350
- Wear marks under the taps
- Staining under the taps and around the waste
About our bath re-enamelling in Moreton Mill
Cast iron, steel, acrylic, roll-top and period baths can all be resurfaced. The finish is sprayed on in several coats over a bonding primer, once the bath has been cleaned, repaired and prepared. We are often asked to fix lots of chips and rust spots and staining under the taps and around the waste, on acrylic baths, Victorian roll-tops and cast iron baths.
The work is covered for a year after we finish. If anything isn’t right, ring us and we will sort it.
- Where
- Moreton Mill (SY4)
- County
- Shropshire
- Warranty
- 12 months on all our work
- Price
- From £350. Free, fixed price from pictures
- Telephone
- 0345 017 0787
- Page updated
- 23 October 2026
Materials and what they mean for the repair
Cast iron
Cast iron baths are the classic candidate for re-enamelling. They’re built to last, and only the surface wears, so resurfacing gives them a new life.
Pressed steel
Steel baths re-enamel well, as long as any rust is dealt with first. Rust around the waste is common on steel, so we pay close attention there.
Places near Moreton Mill
More services for Moreton Mill
For landlords and businesses
Letting agents often send us photos straight from the inventory. That means we can quote before you even visit the property, and we liaise with tenants about access if you’d like us to.
We also carry out snagging repairs for builders and developers, fixing chips and scratches before handover. We’re CHAS, Constructionline and SafeContractor accredited.
Common questions in Moreton Mill
Is repairing better than replacing?
Generally, yes. A repair skips the removal, fitting and redecorating. If it is not worth repairing, we’ll tell you.
Can landlords book you?
We do, regularly. We quote for multiple addresses and fit around tenancy changeovers.
Do I need to be at home?
We need someone to let us in. You do not need to watch us work.
Can a failed resurfacing be redone?
Yes, we do this regularly. Removing the old finish takes extra time, which we include in the price.
Can you re-enamel a roll-top bath?
Yes, roll-tops are a big part of our work. The inside is resurfaced, and we can refinish the outside as well.
Is it safe with children and pets around?
Keep pets and children away from the work area on the day, so the repair isn’t disturbed while it cures.
When can you do it?
Your quote comes with available dates. Tell us if you need it done quickly.
What information do you need?
Photos of the damage, a photo of the whole bath and your postcode. Then we’ll agree a date.
Looking after it afterwards
After the repair has cured, a few habits help it last:
- Keep suction mats out of the bath
- Don’t leave a chip unrepaired
- Leave the bath for the full curing time before using it
- Clean with a soft cloth and mild detergent
The first few days matter most: give it the full curing time, then clean it gently. After that, no abrasives and no suction mats.
If a previous coating is starting to peel, don’t pick at it. Water gets under it and the damage spreads, so it’s better to have it stripped and redone.
When a repair is not the answer
Some jobs are not right for a repair, for example:
- A cast iron or steel bath that’s cracked right through
- Damage hidden under a previous coating, until it’s stripped back
- Acrylic that moves when you stand in it
If in doubt, send photos and we will say what we think before booking.
What we work on
- Acrylic baths
- Pressed steel baths
- Cast iron baths
- Victorian roll-tops
- Basins & shower trays
How it works
On the day, the technician arrives at the agreed time, protects the room with dust sheets and masking and gets started. The job usually takes a full day. We tidy up before we leave and tell you when it’s ready to use.
- The room is masked, protected and ventilated.
- Next we degrease the bath and fix chips and rust spots.
- The surface is prepared and a bonding primer applied.
- We spray on the new enamel finish in several coats.
- We leave it to cure, and it’s generally ready the day after.
Preparing for the visit
- Tell us about parking, stairs or access
- Keep children and pets away from the room on the day
- Point us to the nearest place to park
Getting a price
You don’t need a survey visit. Photos are enough for us to price nearly every job: we need a close-up, a wider picture and your postcode, and we’ll reply with a fixed quote.
Related advice
About Moreton Mill
Moreton Mill is about 8 miles north-east of Shrewsbury, in Shropshire. We work in every kind of home, from flats and terraces to detached houses and new builds, plus businesses and rented homes. Moreton Mill is one of 433 towns and villages in Shropshire we cover. You can also see our page for Birmingham, about 38 miles away.
Here we cover the SY4 postcode area. Neighbouring places we cover include Edgebolton (1 mile south), Shawbury (1 mile south-west), Walton (3 miles south-east), High Ercall (3 miles south) and Astley (4 miles south-west). Within a short drive, we also cover Shrewsbury (8 miles south-west), Madeley (13 miles south-east), Market Drayton (9 miles north-east), Coleham (8 miles south-west), Kingsland (8 miles south-west) and Whitchurch (12 miles north).
Near you in Moreton Mill
Locally, our jobs take us to homes close to Church of St Andrew and the streets around them. Moreton Mill’s nearest station is Yorton station, about 4.5 miles west. Further afield, we also cover the area around Moreton Corbet Castle (1 mile west). Not far away are Hawk Lake.
Prices and what affects them
Resurfacing from £350. You will know the full cost before booking. We look at:
- Access to the area
- Any earlier repairs that need removing first
- The material and finish
- The size and number of damaged areas
We do not add extras on the day. What we quote from your photos is what you pay, unless the damage turns out to be different, in which case we talk to you first.
Getting a price from photos
You can take the photos on your phone. Just make sure we can see:
- Something in shot to show the size
- Daylight if possible, and no flash reflection
- A clear, close picture of the problem area
- What it’s made of, if you know
The quickest way to a price is to send two or three pictures through our quote form or call us. We’ll tell you honestly whether it can be repaired.
Do you need bath re-enamelling in Moreton Mill?
Enamel doesn’t fail overnight. Years of cleaning, hard water and hot baths dull the surface, usually first under the taps and around the waste.
These are the problems we’re asked about most:
- A period or roll-top bath worth keeping
- Wear marks under the taps
- A coloured bath you want in white
- A peeling or bubbling previous coating
What your quote should include
- Whether a trained technician does the job
- What happens if the damage is worse than the pictures show
- What prep work is covered
- How your room will be protected
Repair or replace: which is better?
There are times replacing is better: a cracked-through bath, a change of size or shape, or a full refit. In most other cases, resurfacing is the better choice. Our bath re-enamelling starts from £350. We charge the same wherever you are, so there is no premium for Moreton Mill. What changes the price is the job itself: how much damage, what it’s made of and how many items.
What you get with us
- Most jobs done in one visit
- Colours mixed by hand to suit your surface
- Dust sheets down, tidy finish
- Free fixed quotes from pictures
Read our pricing and resurfacing vs replacement cost guide.
About our accreditations · Every repair comes with a one-year guarantee.
