Swansea · Wales
Bath Re-enamelling in Port-Eynon
Problem with your bath in Port-Eynon? We put it right where it is, mix the colour on the day and back it with a one-year guarantee.
- Resurfacing from £350
- Stains that will not shift
- A coloured bath you want in white
What your bath is made of matters
Pressed steel
Steel baths re-enamel well, once any rust has been treated. Steel often rusts by the plughole, so we pay close attention there.
Acrylic
We resurface acrylic baths as well, using a system that bonds to acrylic. The bath needs to be firm and well supported for the finish to last.
About our bath re-enamelling in Port-Eynon
We resurface cast iron, steel and acrylic baths, including roll-tops and period baths. The finish is sprayed on in several coats over a bonding primer, once the bath has been cleaned, repaired and prepared. Typical jobs include an original cast iron bath that needs restoring and a coloured bath you want in white, across cast iron baths, pressed steel baths and Victorian roll-tops.
A one-year guarantee comes as standard.
- Where
- Port-Eynon (SA3)
- County
- Swansea
- Cover
- A year, on every repair
- Quote
- From £350. Fixed and free, based on photos
- Telephone
- 0345 017 0787
- Last updated
- 23 October 2026
What we’re called out for in Port-Eynon
Enamel does not fail overnight. Abrasive cleaners, limescale and years of use dull the surface, starting where water runs and sits.
Look out for these signs:
- Lots of chips and rust spots
- A bath that stays dull however much you clean it
- An old resurfacing that’s failing
- An outdated colour you’d like to change
Before you book anyone
- What the guarantee covers, and for how long
- How the room is protected while they work
- How soon you can use it again
- Who turns up on the day
How it works
You don’t need to empty the room beforehand. Everything we use comes in the van with us, put protection down and start once you are happy with the plan. Most jobs take most of the day, and you’re welcome to carry on with your day while we work.
- We check the bath and agree the finish with you.
- Everything around the bath is masked and covered.
- The bath is degreased, repaired and keyed.
- We apply the primer and then the finish coats.
- We remove the masking, tidy up and give you the curing time.
Before we arrive
- Keep a parking space free if you can
- Mention if the room is upstairs or in a flat
- Avoid using the area for a few hours before we arrive
Getting a price
Upload pictures of the damage and one of the whole item, with your SA3 postcode, and we will reply with a fixed price.
Read more
Aftercare tips
Much of the damage we repair could have been avoided. A few tips:
- A quick wipe after use keeps limescale away
- Fix dripping taps quickly
- Clean with a soft cloth and mild detergent
- Do not use the bath until it has fully cured
Give the finish its full curing time before using the bath. After that, a soft cloth and washing-up liquid is all it needs.
Leave a peeling coating alone. Moisture gets underneath and makes it worse, so have it stripped and resurfaced.
DIY repairs versus a professional job
If you do try a kit, read the instructions carefully, and give it the full curing time. If it fails, we can still put it right.
A DIY attempt isn’t a disaster. We remove the old filler and start again, so it doesn’t stop a professional repair. Just mention it when you send pictures, as it can add time.
Your questions about bath re-enamelling in Port-Eynon
Do you need to take the bath out?
No. We resurface it in place, so the tiles and taps stay put.
Is there any odour?
A little, depending on the job. Ventilation keeps it to a minimum, and it soon fades.
Do you come to Port-Eynon?
We do. We send a technician to Port-Eynon for every job, and the price is the same as everywhere else.
Can pets and children be at home?
Keep pets and children away from the work area on the day, so the repair is not disturbed while it cures.
Can you re-enamel a roll-top bath?
Yes, roll-tops are a big part of our work. We resurface the inside, and the outside can be refinished too.
What if the damage is worse than the pictures show?
The price is fixed for what the pictures show. Anything extra is discussed before we begin.
When can you do it?
It depends on the time of year and where you are. Send pictures with your postcode and we will reply with the earliest dates.
Can a failed resurfacing be redone?
Typically, yes. The old coating comes off before we resurface it. Mention it when you send photos.
Why repair rather than replace?
Getting a cast iron bath out is hard work: it’s very heavy, may need breaking up, and the replacement can be costly. Re-enamelling avoids all of it. Our bath re-enamelling starts from £350. Set against the cost of replacement, repairing typically costs far less, because there’s no removal, plumbing or making good. The quote lists exactly what you’re paying for.
Why us?
- Most jobs done in one visit
- Work done at your home or business
- We leave the room as we found it
- Same prices wherever you are
See our pricing and bath cost comparison.
Nearby places to Port-Eynon
What else we do in Port-Eynon
What bath re-enamelling costs
Resurfacing from £350. We price every job individually. The main factors are:
- Any earlier repairs that need removing first
- Doing more than one item at once
- How much damage there is
- The material and finish
There are no surprise extras on the day. What we quote from your photos is what you pay, and if the damage turns out to be different, we discuss it before starting.
How to get a fixed price
The better the photos, the more accurate the price. Here’s what helps:
- A picture taken from further back
- A coin beside the damage so we can judge size
- A clear, close picture of the problem area
- The material, if you know it
There is no need for us to visit first. Nearly every job can be priced from pictures: send a close-up, a wider shot and your postcode, and we will reply with a fixed price.
Where we work around Port-Eynon
Port-Eynon is about 10 miles south of Llanelli, in Swansea. We work in every kind of home, from flats and terraces to detached houses and new builds, as well as offices, shops and holiday lets. Our repair technicians cover 153 places across Swansea, from the larger towns to small villages.
Here we cover the SA3 postcode area. If you are just outside Port-Eynon, we cover Scurlage (1 mile north), Middleton (3 miles north-west), Reynoldston (3 miles north), Rhossili (3 miles north-west) and Llangennith (4 miles north-west). Larger places within reach include Swansea (13 miles north-east), Castle (13 miles north-east), Morriston (15 miles north-east), Mount Pleasant (13 miles north-east), Gorseinon (11 miles north-east) and Dyfaty (13 miles north-east).
Local landmarks in Port-Eynon
Our customers here include homes close to The Ship Inn, among other places. Nearby you’ll also find Gower Farm Museum & Tourist Centre (2.3 miles north) and Port Eynon Castle (within half a mile south-east). Open spaces near Port-Eynon include Serpentine Lake and Hangman's Cross Hill.
Work for landlords and builders
We carry out planned and one-off repairs for housing associations and facilities teams in Swansea and across the UK. Repairing in place avoids the disruption of a replacement, which is easier on the people living there.
If you manage property in Port-Eynon, we’ll quote for several properties at once. Send photos for each one and we will come back with a combined price.
About our accreditations · Every repair comes with a one-year guarantee.
