Doncaster · England
Bath Re-enamelling in Styrrup
Fixed-price bath re-enamelling in Styrrup and the surrounding area, done in a single visit in most cases and guaranteed for a year.
- Resurfacing from £350
- Wear marks under the taps
- Lots of chips and rust spots
When we would advise against a repair
We won’t take on work that won’t last, so these are the limits:
- Plumbing leaks, which need a plumber
- A metal bath with a through crack
- A bath that is rusted through
Not sure? Send photos and we’ll give you a straight answer.
Surfaces we repair
- Acrylic baths
- Victorian roll-tops
- Pressed steel baths
- Cast iron baths
- Basins & shower trays
About our bath re-enamelling in Styrrup
When a bath is structurally fine but worn out on the surface, resurfacing is normally the best value. There is no removal, plumbing or tiling involved. Whether it’s staining under the taps and around the waste and a peeling or bubbling previous coating, we can help, on acrylic baths, Victorian roll-tops and pressed steel baths alike.
All our work comes with our one-year guarantee.
- Where
- Styrrup (DN11)
- Area hub
- Doncaster
- Warranty
- 12 months on all our work
- Price
- From £350. Fixed and free, based on photos
- Telephone
- 0345 017 0787
- Page updated
- 23 October 2026
Repairs by material
Roll-top and period baths
We can resurface a roll-top inside and out, with the outside refinished as well.
Cast iron
A cast iron bath is heavy enough that most people never want to move it. Only the enamel surface wears or chips, and that is what we repair.
Styrrup and the surrounding area
Styrrup is about 5 miles east of Maltby, in Doncaster. Our work suits any type of property, old or new, large or small, as well as offices, shops and holiday lets. We cover 89 places across Doncaster. Our jobs stretch from Styrrup to Leeds (34 miles away).
Our technicians cover all of the DN11 postcode area and the streets around it. Jobs here include addresses on Main Street, Pagdin Drive and Pinfold Lane and the roads around them. We also travel to Harworth (1 mile north-east), Bircotes (1 mile north-east), Scrooby (3 miles east), Bawtry (3 miles north-east) and Austerfield (4 miles north-east). Within a short drive, we also cover Doncaster (8 miles north), Adwick le Street (12 miles north), Thorne (15 miles north), Conisbrough (8 miles north-west), Bentley (10 miles north) and Armthorpe (9 miles north).
Near you in Styrrup
We visit homes around Church of All Saints, Serlby Park Academy and Harworth CofE Academy and the streets around them. Nearby you’ll also find Hospital of St Mary Magdalene (3 miles north-east) and Tickhill Castle (1.8 miles north-west).
How to look after the repair
It’s all simple stuff, just a few sensible habits:
- Never use suction bath mats
- Keep toiletries on a shelf rather than in the bath
- Use washing-up liquid and a soft cloth
- Dry the bath after use to stop limescale
A quick rinse and wipe after use helps, particularly where water is hard, to stop limescale building up.
Leave a peeling coating alone. Moisture gets underneath and makes it worse, so it’s better to have it stripped and redone.
Why repair rather than replace?
There are times replacing is better: a cracked-through bath, a change of size or shape, or a full refit. Otherwise, resurfacing generally wins. Our bath re-enamelling starts from £350. A few things move the price: access, material, the extent of the damage and whether we can do several items together. Send pictures and you’ll get a fixed figure.
What you get with us
- Same prices wherever you are
- Colours mixed by hand to suit your surface
- Fixed prices from your pictures
- CHAS and Constructionline accredited
Take a look at our full price list and resurfacing vs replacement cost guide.
Also near Styrrup
What else we do in Styrrup
What we do, step by step
We begin by going over the job with you, so you know exactly what we’re doing. After that, protection goes down around the work area and the work begins. You can expect it to take a full day, and we’ll tell you if anything changes.
- First we look the bath over and confirm the finish.
- Taps, tiles and the floor are masked off.
- The bath is degreased, repaired and keyed.
- Primer and finish coats are applied.
- We remove the masking, tidy up and give you the curing time.
Before we arrive
- Tell us about any previous repairs or coatings
- Open a window if you can
- Keep a parking space free if you can
Ask for a price
For a price in Styrrup, the easiest route is photos: a close-up, a wider shot and your postcode. We reply with a fixed quote and our next available dates.
Read more
When to call us in Styrrup
Many baths we resurface have simply been well used. Underneath, a cast iron or steel bath is typically as strong as ever.
Signs it’s time to call us include:
- Worn patches where water runs and sits
- Lots of chips and rust spots
- A coating lifting around the plughole
- Stains that will not shift
Comparing quotes
- Whether the colour is mixed to match
- Whether a trained technician does the job
- How to look after the finish
- What the guarantee covers, and for how long
For landlords and businesses
We work for landlords, letting agents and housing providers in Styrrup as well as homeowners. A repair between tenants keeps the property empty for less time, and it normally costs far less than a refit.
We regularly price jobs from inventory or check-out pictures. You can have a price before you arrange access, and we liaise with tenants about access if you’d like us to.
Styrrup questions
Will the new finish last?
A well-prepared finish lasts a long time if it’s looked after. Gentle cleaning, no suction mats.
Do the materials smell?
There can be some smell while we work. It fades as everything cures.
Someone resurfaced my bath and it’s peeling. Can you help?
Yes. Removing the old finish takes extra time, which we include in the price.
Are there extra charges for Styrrup?
We don’t add a call-out fee. Your fixed price includes everything.
Is a repair better than a new one?
Generally, yes. A repair skips the removal, fitting and redecorating. We’ll be honest if it’s not worth it.
Do you resurface freestanding baths?
Yes. Inside and out.
Are you accredited?
Yes, including CHAS, Constructionline and SafeContractor. The full list is on our accreditations page.
How long does re-enamelling take?
Normally a day, then it’s ready to use the following day. Deeply pitted baths may need a second day.
Can I fix it myself?
It’s natural to want to try a repair yourself. The risk is that a kit repair hides the damage for a while, then fails, and then the old filler has to be removed first.
DIY kits are sold for most surfaces, and they can make a small mark look better. Where they fall down is colour and preparation: they come in a handful of shades, and if the surface is not prepared the repair will not last.
About our accreditations · Every repair comes with a one-year guarantee.
