Wiltshire · England
Bath chip & crack repair in Brookside, Wiltshire
Fixed-price bath repair in Brookside and the surrounding area, normally in one visit and guaranteed for a year.
- Repairs from £95
- Deep scratches in acrylic
- Chips along the edge of the bath
How to look after the repair
Nothing complicated is needed, just a few sensible habits:
- Don’t leave a fresh chip for long
- Rinse the bath after use, especially in hard water areas
- Put a towel in the bath if you’re working above it
- A dripping tap stains enamel, so fix it early
Give the repair the full curing time we recommend before using the bath. After that, gentle cleaning keeps it looking good.
A chip on a metal bath shouldn’t be left. Water gets to the metal and rust starts, turning a quick repair into a bigger one.
About our bath repair in Brookside
A typical bath repair is a few hours’ work, and you can typically bathe again the following day. You won’t need a plumber or tiler, because nothing is disconnected. Whether it’s rust by the waste and overflow and a chip where the taps sit, we can help, whatever the material.
The work is covered for a year after we finish. If anything is not right, ring us and we will come back.
- Area
- Brookside (SN15)
- Area hub
- Wiltshire
- Cover
- 12 months on all our work
- Price
- From £95. Fixed and free, based on pictures
- Phone
- 0345 017 0787
- Page updated
- 23 October 2026
Honest limits
We will not take on work that won’t last, so these are the limits:
- A bath worn all over, where resurfacing makes more sense
- Leaks from the waste or overflow fittings (a plumber’s job)
- Cracks in acrylic we can’t reach from underneath
If in doubt, send photos and we’ll say what we think.
Materials we repair
- Acrylic
- Cast iron enamel
- Roll-top & freestanding
- Pressed steel enamel
- Whirlpool & spa baths
Repair or replace: which is better?
A new bath brings a chain of other jobs: the tiles sitting on the rim tend to break, a new panel is frequently needed, and the plumbing has to be disconnected and refitted. Repairing the damage avoids all of that. Repairs from £95, with every job priced individually. Most people are surprised how affordable a repair is, particularly next to the cost of replacement. Photos let us give you the exact figure.
Why book with us
- One-year guarantee on every repair
- Same prices wherever you are
- Most jobs done in one visit
- Rooms protected and left tidy
See our prices page and bath cost comparison.
Our work in Brookside
Brookside is about 4 miles north-east of Chippenham, in Wiltshire. Whether you’re in the middle of Brookside or on the outskirts, the service is the same: a fixed quote, a tidy visit and a guarantee. Our technicians cover all 425 towns and villages across Wiltshire, from the larger towns to small villages. We work right across the region, from Brookside to Birmingham (67 miles away).
Jobs in SN15 are booked in the same way as anywhere else. We also travel to Sutton Benger (1 mile south), Upper Seagry (1 mile north), Christian Malford (1 mile east), Upper Town (2 miles east) and Great Somerford (2 miles north-east). Further out, we also cover Trowbridge (14 miles south-west), Chippenham (4 miles south-west), Calne (6 miles south-east), Devizes (12 miles south), Melksham (10 miles south) and Corsham (8 miles south-west).
Local landmarks in Brookside
Around Brookside, we work in homes near La Flambé Restaurant pub, Sutton Benger Church of England Aided Primary School and Church of All Saints. Brookside’s nearest station is Chippenham station, about 3.9 miles south-west. Well-known places in the area include Chippenham Community Hospital (4.7 miles south-west) and Great Somerford (2.5 miles north-east). Not far away are Great Wood.
When to call us in Brookside
A cracked acrylic bath typically wasn’t supported properly. Legs that aren’t adjusted, a missing cradle or a soft floor let the bath move.
You may need us if you’ve spotted:
- An old repair that has yellowed or come loose
- Snagging damage from a refit
- Rust spots around the plughole
- Cracks in an acrylic bath
Comparing quotes
- How the colour is matched
- Aftercare advice
- How long it needs to cure
- How changes to the job are handled
What we do, step by step
We agree an arrival time beforehand, so you’re not left guessing. Once we are there, the work takes a few hours, depending on the damage in most cases. We leave the room clean and you will know when it can be used.
- We clean the area and remove any loose enamel or rust.
- Next we fill the damage and sand it smooth and level.
- We tint the finish on the day to suit your bath’s shade of white or colour.
- We build up the finish and polish it into the surrounding enamel.
- We leave it to cure; you can generally use the bath the following day.
Preparing for the visit
- Let us know if it has been repaired before
- Let the surface dry out before the visit
- Mention any parking restrictions or tricky access
How to get a price
Getting a price is easy: snap the damage close up and then the whole item, send them over with your postcode, and we will reply with a fixed price. There’s no charge for the quote and you are under no obligation.
Read more
Your questions about bath repair in Brookside
I tried a repair kit. Can you fix it?
Yes, we do this often. We strip it out, deal with any rust and repair it again.
What happens once I’ve sent pictures?
You get a fixed quote and available dates. If anything’s unclear, we’ll ask for another photo.
Is the work guaranteed?
Yes: twelve months. If anything goes wrong with the repair within the year, we return to fix it.
How long before I can use the bath?
Normally by the following day, depending on the repair.
Is it messy?
Very little mess: we sheet and mask everything nearby, and we leave the room clean.
Do you hold any accreditations?
Yes, including CHAS, Constructionline and SafeContractor. The full list is on our accreditations page.
Will the repair show?
The goal is a repair that blends in. How well it disappears depends on the condition of the rest of the bath, and we will tell you what to expect.
Can you redo someone else’s repair?
Most of the time. Let us know what was used before and we’ll plan for it.
For landlords and businesses
Builders, developers and site managers book us for snagging repairs, putting right damage done during fitting so nothing needs replacing. We are CHAS, Constructionline and SafeContractor accredited.
We’re used to working with agents and managing companies. Just send pictures, the address and how to get access.
Materials and what they mean for the repair
Pressed steel
Under the enamel of a steel bath is thin metal. Once a chip exposes it, rust follows quickly, so we treat and seal the metal before filling.
Composite and resin
Composite baths are dense and solid. Chips and scratches can be filled and colour matched, in much the same way.
What bath repair costs
Prices start from £95. Quotes are free and the price is fixed. What we look at:
- The size and number of damaged areas
- Unusual colours or finishes
- Whether old repairs or coatings need taking off
- The material
Rather than charging by the hour, we fix the price before we start. It depends on the damage, the material and access, and doing several items at once reduces it.
Quotes from your pictures
Photographing the damage takes a minute. Please include:
- The postcode, so we can plan the visit
- Something in shot to show the size
- A picture taken from further back
- A clear, close picture of the problem area
We price from pictures so you don’t have to wait in for a survey. Send them through the quote form, or call 0345 017 0787 if you’d rather talk it through, and we’ll come back with a fixed figure.
Also near Brookside
What else we do in Brookside
About our accreditations · Every repair comes with a one-year guarantee.
