Perth and Kinross · Scotland
Bath Repair for Almondbank homes
Chip and crack repairs to enamel, acrylic and cast iron baths in Almondbank, carried out at your home and guaranteed for a year.
- Repairs from £95
- A chip where the taps sit
- Rust spots around the plughole
How we handle bath repair in Almondbank
Bath repair is our most common job. Chips on the rim, rust around the waste and cracks in acrylic are all repaired in place, normally in a single visit. We’re often asked to fix damage beneath the taps and chips caused by builders, in pressed steel enamel, cast iron enamel and acrylic.
Every job is backed for twelve months, and the guarantee is the same wherever you live. We return to put right any problem with the work.
- Where
- Almondbank (PH1)
- County
- Perth and Kinross
- Cover
- A year, on every repair
- Price
- From £95. Free and fixed, from your photos
- Call
- 0345 017 0787
- Page updated
- 23 October 2026
How it works
We turn up when we said we would, introduces themselves and checks the damage against your photos first. Dust sheets and masking tape go down before we open a single tin. Most visits take a morning or an afternoon, and we leave the room as we found it.
- First, the area is cleaned and any loose enamel or rust is removed.
- Next we fill the damage and sand it smooth and level.
- We mix the colour on the day to match your bath’s exact shade.
- We build up the finish and polish it into the surrounding enamel.
- Once it has cured, typically by the following day, the bath is ready to use.
Preparing for the visit
- Tell us about any previous repairs or coatings
- Keep pets and children out of the room while we work
- Move bottles, mats and clutter away from the area
Get a quote
Send us photos of the damage and one of the whole item, with your PH1 postcode, and we will come back with a fixed quote.
Read more
Our work in Almondbank
Almondbank is about 3 miles north-west of Perth, in Perth and Kinross. We travel to clients in Almondbank, so there’s no workshop to go to. Almondbank is one of 107 places in Perth and Kinross where we work. You can also see our page for Edinburgh, about 35 miles away.
We work across PH1 and the streets around it. You will find streets such as Main Street, College Mill Road and Roman Road, all of which we cover. We also travel to Pitcairngreen (1 mile north), Ruthvenfield (1 mile south-east), Huntingtower (1 mile south-east), Tibbermore (2 miles south-west) and Hillyland (2 miles south-east). Further out, we also cover Perth (3 miles south-east), Blairgowrie and Rattray (14 miles north-east), Crieff (13 miles west), Auchterarder (11 miles south-west), Kinross (15 miles south) and Scone (4 miles east).
Local landmarks in Almondbank
Typical jobs here are in homes near Bertha Park High School and St Serf's Church, among other places. The nearest railway station is Perth station, roughly 3.5 miles south-east of the centre. Further afield, we also cover the area around St John's Shopping Centre (3.6 miles south-east) and Huntingtower Castle (1.2 miles south-east). For a walk, there’s Mailer Hill and Dupplin Lake.
Prices and what affects them
Repairs from £95. There’s no charge for travel to Almondbank. The price comes down to:
- The material and finish
- Whether old repairs or coatings need taking off
- Doing more than one item at once
- The size and number of damaged areas
We charge the same wherever you are, with no extra for Almondbank. What changes the price is the job itself: how much damage, what it’s made of and how many items.
Getting a price from photos
Most quotes are done from photos alone. To make it quick:
- A picture taken from further back
- A coin or ruler next to the damage for scale
- A close-up of the damage, in focus
- Natural light rather than flash
Pricing is simple: take a close-up of the damage and a picture from further back, send them over with your postcode, and you will get a fixed quote back. Quotes are free and you’re under no obligation.
Aftercare tips
It’s all simple stuff, just a few sensible habits:
- Keep metal cans and razors off the surface
- Protect the bath with a towel when doing jobs nearby
- Check that an acrylic bath doesn’t move when you stand in it
- Do not scrub with anything abrasive
Use gentle, non-abrasive cleaners and try not to drop heavy bottles on the repair. Deal with new chips early, before rust sets in.
If an acrylic bath has a crack, stop showering in it until it’s repaired. Every use opens the crack a little more, and water can get through to the floor below.
DIY kit or professional repair?
What a professional repair adds is preparation, colour matching and finishing. We prepare the area properly, mix the colour on site and polish the finish to match, then guarantee it for a year.
If you are set on a kit, follow its instructions closely, ensure the area is clean and completely dry, and do not use it until it has fully cured. If it fails, we can still put it right.
Places near Almondbank
What else we do in Almondbank
Repairs by material
Pressed steel
Under the enamel of a steel bath is thin metal. Once a chip exposes it, rust follows quickly, so we treat and seal the metal before filling.
Acrylic
Acrylic is light and warm to the touch, but it relies on good support. Cracks are strengthened from behind before the front is finished.
What a repair cannot fix
A repair is not always the answer, and we will tell you before we start. We can’t fix:
- A bath that flexes because its feet or cradle have failed (that needs fixing first)
- A bath worn all over, where resurfacing makes more sense
- Acrylic cracks with no access behind them
Send us pictures and we’ll tell you honestly.
Materials we work on in Almondbank
- Roll-top & freestanding
- Cast iron enamel
- Whirlpool & spa baths
- Acrylic
- Pressed steel enamel
Should you replace it?
A new bath costs more than the bath itself: taking out the old one, plumbing, tiling, a panel and redecorating. A repair is one job, done in one visit. Prices start from £95. The price depends on how much damage there is and what kind, the material and how many jobs we combine into one visit. We give a fixed quote from your photos, so you know the cost before you book.
Why Almondbank clients choose us
- A year’s guarantee on all work
- We come to you, anywhere in the UK
- Fixed prices from your pictures
- Colour-matched on site
Read our pricing or guide to resurfacing and replacement costs.
Signs you need bath repair in Almondbank
Baths take more knocks than people expect: bottles, shower heads and razors are dropped every day, and fittings press hard against the enamel. Over time, chips and rust spots are almost inevitable.
Typical reasons for a call-out include:
- Deep scratches in acrylic
- A chip where the taps sit
- Impact holes in acrylic
- Rust by the waste and overflow
Questions to ask before you book
- The length of the guarantee and what it covers
- Whether the colour is mixed to match
- How the room is protected while they work
- How soon you can use it again
Almondbank questions
What happens if you find more damage?
If we find something the photos didn’t show, we explain it first. The price only changes if you agree.
Is there any odour?
A little, depending on the job. Ventilation keeps it to a minimum, and it soon fades.
How invisible is a bath repair?
We aim for a repair you cannot easily find. The rest of the bath’s condition makes a difference.
Can a cracked acrylic bath be fixed?
Normally, yes, if we can reach the underside to reinforce it. Check under the bath panel, or send us a photo.
Can I add another job to the visit?
Yes. Combining jobs on one visit brings the cost down. Include photos of each item.
Do you cover the entire of Perth and Kinross?
We work UK-wide. Prices do not change with location.
Is it messy?
We protect the room with dust sheets and masking first, and we clean up when we’ve finished.
Can you fix rust around the plughole?
Yes. We remove the rust and loose enamel, seal and fill the area, then colour-match the finish.
About our accreditations · Every repair comes with a one-year guarantee.
