Wiltshire · England
Bath Repair for Milbourne homes
Chip and crack repairs to enamel, acrylic and cast iron baths for householders, landlords and businesses in Milbourne. Send photos for a free, fixed quote.
- Repairs from £95
- Hairline or through cracks in acrylic
- Chips along the edge of the bath
Should I try a DIY kit first?
If you are set on a kit, follow its instructions closely and work on a clean, dry surface, and do not use it until it has fully cured. If it does not work out, we can still repair it properly.
What a professional repair adds is preparation, colour matching and finishing. We clean and key the area properly, mix the colour to your surface and finish it to the same sheen, then guarantee it for a year.
Bath repair in Milbourne, done in place
Most bath damage, from chips and cracks to rust spots and holes, is repaired in place. Nothing is unplumbed, the tiles are not touched, and the finish is matched to the rest of the bath. We work on whirlpool & spa baths, acrylic and pressed steel enamel, and people most often call us about chips on the rim or sides and an old repair that has yellowed or come loose.
You are covered for a year from the day of the repair. Just call us if there’s a problem and we’ll sort it.
- Location
- Milbourne (SN16)
- County
- Wiltshire
- Guarantee
- One year on every repair
- Quotes
- From £95. Free, fixed quote from pictures
- Telephone
- 0345 017 0787
- Last updated
- 23 October 2026
Towns and villages near Milbourne
Other services in Milbourne
What your bath is made of matters
Acrylic
Acrylic baths are moulded sheet reinforced underneath. They don’t rust, but they can crack, scratch or be holed, and a crack only stays repaired if it’s supported underneath.
Pressed steel
Steel baths and trays have a thin metal body under the enamel. Exposed steel rusts quickly, so the metal is treated and sealed before the repair.
FAQs for Milbourne
Will the repair last?
Done properly, a repair lasts for years, and ours come with a one-year guarantee. Gentle cleaning helps it last.
Will the repair show?
On a bath in good condition, a colour matched repair is very hard to spot. On older, dull enamel the repair can look glossier than the area around it.
Can landlords book you?
Yes, often. We quote for multiple addresses and fit around tenancy changeovers.
Do you cover the entire of Wiltshire?
Everywhere in the UK, Milbourne included. Travel is included in the price.
What if the damage is worse than the pictures show?
Your quote covers the damage in the photos. Anything extra is discussed before we begin.
It’s been repaired before. Can you still fix it?
Generally, yes. Tell us what was done before.
Something went through my bath. Can it be fixed?
Normally. Send us a photo of the hole and one from under the bath if you can.
Will there be a smell?
It depends on the job, but often a little. Ventilation keeps it to a minimum, and it soon fades.
Signs you need bath repair in Milbourne
Rust tends to begin where water collects, by the plughole, beneath dripping taps or in an unrepaired chip. Once water reaches the steel or iron, rust spreads under the enamel.
Typical reasons for a call-out include:
- Hairline or through cracks in acrylic
- Rust spots around the plughole
- An old repair that has yellowed or come loose
- Holes from dropped items
Before you book anyone
- Who turns up on the day
- Whether cleaning and preparation are in the price
- How the colour is matched
- How to care for the finish
What bath repair costs
Repairs from £95. You will not pay by the hour. The price is based on:
- What kind of damage it is
- What the surface is made of
- Whether we combine several jobs
- Access to the area
It helps to know what pushes a price up or down: the amount of damage, the material, access to the area, and how many jobs we do in one trip. Photos let us give you a fixed figure.
How to get a fixed quote
A couple of clear pictures is all it takes. Try to include:
- Any details about the material
- Something in shot to show the size
- One sharp close-up of the damage
- A wider photo showing the whole bath
Most customers in Milbourne get their price from photos. Tell us what happened and where you are, and we will reply with a fixed quote and the earliest dates we have.
Work for landlords and builders
Rental properties take more wear, and replacing items every time a tenant leaves is expensive. A repair between tenancies is a cheaper way to keep the property in good order.
Builders use us to fix snagging damage before handover, saving last-minute replacements. Several plots can be done in one visit.
Repairing versus replacing in Milbourne
A new bath brings a chain of other jobs: the tiles sitting on the rim tend to break, a new panel is often needed, and a plumber has to disconnect and reconnect everything. Repairing the damage avoids all of that. Our bath repair starts from £95. No two jobs are quite the same, so we price each one individually. The size and type of damage, the material and access all make a difference, and combining jobs on one visit brings the cost down.
Why us?
- Nothing taken out or refitted
- Honest advice, even when it means no job
- CHAS and Constructionline accredited
- A year’s guarantee on all work
See our full price list and guide to resurfacing and replacement costs.
Our work in Milbourne
Milbourne is about 9 miles north of Chippenham, in Wiltshire. Customers in Milbourne get the same service as everywhere else we cover: a fixed quote from your photos, and a technician at your door on the day. Milbourne is one of 425 towns and villages in Wiltshire where we work. Our nearest city page is Birmingham, about 61 miles away.
Here we cover the SN16 postcode area. We regularly work on streets such as Milbourne Park, Milbourne Lane and Monks Park and the roads around them. Nearby, we also work in Malmesbury (1 mile west), Lea (1 mile south-east), Charlton (1 mile north-east), Charlton Heath (2 miles east) and Little Somerford (3 miles south-east). Further out, we also cover Chippenham (9 miles south), Calne (11 miles south), Melksham (15 miles south), Corsham (12 miles south-west), Hardenhuish (9 miles south) and Lyneham (8 miles south-east).
Landmarks near Milbourne
Typical jobs here are in homes near St Aldhelm's Roman Catholic Church, Malmesbury Church of England School and Music Academy and St Joseph's Catholic Primary School. A little further out are Athelstan Museum (0.7 miles south-west) and Malmesbury Castle (0.7 miles south-west).
What happens on the day
Expect a friendly, tidy visit. We agree the arrival time in advance, cover and mask the work area, and get on with the job, which normally takes a few hours, depending on the damage. If we find something your photos didn’t show, we’ll explain it before carrying on.
- First, the area is cleaned and any loose enamel or rust is removed.
- We fill the damage and sand it flush with the surrounding surface.
- We tint the finish on the day to suit your bath’s shade of white or colour.
- Finish coats go on, then the repair is polished to blend in.
- The repair is left to cure, and most baths can be used the day after.
Before we arrive
- Point us to the nearest place to park
- Tell us if there are stairs or a lift
- Let us know if it has been repaired before
Getting a price
Call 0345 017 0787 or use the quote form. With a clear picture of the damage and one of the entire bath, we can price the job without visiting.
Advice
Aftercare tips
How the surface is treated afterwards matters:
- Store metal items away from the bath
- If an acrylic bath flexes, have its feet adjusted
- Protect the bath with a towel when doing jobs nearby
- Use a soft cloth and washing-up liquid for everyday cleaning
Use gentle, non-abrasive cleaners and try not to drop heavy bottles on the repair. Deal with new chips early, before rust sets in.
Until we visit, a strip of waterproof tape over the damage helps, to keep water out. Remove it before the repair.
About our accreditations · Every repair comes with a one-year guarantee.
