Perth and Kinross · Scotland
Bath re-enamelling & resurfacing in Perth, Perth and Kinross
Local bath re-enamelling for Perth: photo quotes, tidy work and a year’s guarantee.
- Resurfacing from £350
- Worn patches where water runs and sits
- An outdated colour you’d like to change
What affects the price in Perth
Resurfacing from £350. There’s no area surcharge for Perth. What changes the price is:
- The material and finish
- Unusual colours or finishes
- Whether old repairs or coatings need taking off
- The size and number of damaged areas
Our prices are the same across the UK, so there’s no premium for Perth. The job itself decides the price: how much damage, what it’s made of and how many items.
Getting a price from pictures
Two or three clear photos are normally enough. It helps if you send:
- Your postcode, so we can check dates
- Something in shot to show the size
- A clear, close picture of the problem area
- One picture of the entire bath
A quote takes minutes to ask for: photograph the damage, then the entire bath, add your postcode and send them to us. You will get a fixed quote, not an estimate.
About our bath re-enamelling in Perth
Many of the baths we re-enamel are period roll-tops, which would be difficult and expensive to replace. Resurfacing them in place keeps the original bath. We work on basins & shower trays, pressed steel baths and acrylic baths, and people most often call us about worn patches where water runs and sits and a roll-top that’s seen better days.
All our work comes with a one-year guarantee.
- Where
- Perth (PH1, PH2)
- Region
- Perth and Kinross
- Cover
- A year, on every repair
- Price
- From £350. Fixed and free, based on photos
- Phone
- 0345 017 0787
- Page updated
- 23 October 2026
Can I fix it myself?
If you are set on a kit, follow its instructions closely and work on a clean, dry surface, and give it the full curing time. If it does not work out, we can still repair it properly.
DIY kits are sold for most surfaces, and they can make a small mark look better. The trouble is colour and preparation: kits come in a few standard shades, and without proper cleaning and keying the filler frequently lifts.
When a repair isn’t the answer
We’ll always be straight with you, so here’s what a repair cannot fix:
- A cast iron or steel bath that is cracked right through
- Plumbing leaks, which need a plumber
- A bath that’s rusted through
Send us photos and we’ll tell you honestly before you book.
What we work on
- Cast iron baths
- Acrylic baths
- Pressed steel baths
- Victorian roll-tops
- Basins & shower trays
What we’re called out for in Perth
Enamel does not fail overnight. Abrasive cleaners, limescale and years of use dull the surface, starting where water runs and sits.
Send us a picture if you notice any of these:
- A roll-top that is seen better days
- A coloured bath you want in white
- Thin, worn enamel in places
- A bath that stays dull however much you clean it
Before you book anyone
- How soon you can use it again
- Whether cleaning and preparation are in the price
- Aftercare advice
- How the room is protected while they work
Places near Perth
Other services in Perth
Our work in Perth
Perth is about 33 miles north of Edinburgh, in Perth and Kinross. Book a date that suits you, and we will give you an arrival time in advance, so you are not left waiting in all day. We cover 107 places across Perth and Kinross, from the larger towns to small villages. We work right across the region, from Perth to Edinburgh (about 33 miles away).
Our visits in PH1 and PH2 are booked in the same way as anywhere else. Streets in the area include Simpson Square, High Street and Moredun Square, and we cover them all. Perth sits on or near the A9 and A85, which makes travel easy. Close by, we cover Oakbank (1 mile south-west), Scoonieburn (2 miles south-east), Tarsappie (2 miles south-east), Milltown of Aberdalgie (3 miles south-west) and Forgandenny (4 miles south). We also work in nearby towns such as Blairgowrie and Rattray (14 miles north), Crieff (15 miles west), Auchterarder (12 miles south-west), Kinross (13 miles south), Coupar Angus (12 miles north-east) and Rattray (14 miles north). As one of the bigger places in Perth and Kinross, Perth is somewhere we visit often.
Landmarks near Perth
We visit homes around Milne Street, St John's Academy and Perth High School, among other places. Also close by are Public House (0.6 miles east) and North Inch (0.8 miles east). The nearest railway station is Perth station, about 0.7 miles south-east of the centre. Well-known places in the area include Murray Royal Hospital (1.2 miles east) and Balhousie Castle (0.6 miles north-east). Not far away are St Magdalene's Hill.
What we do, step by step
On the day, we arrive at the time we have agreed, cover the area with dust sheets and masking, and set to work. The job normally takes most of the day. We clean up when we are done and tell you when it’s ready to use.
- The bathroom is protected and ventilation set up.
- Old sealant is cut out and the bath is deep cleaned.
- Chips, rust and pitting are repaired.
- We key the bath and apply a bonding primer.
- The new finish is sprayed on in several coats and left to cure.
How to prepare
- Mention any earlier repairs or resurfacing
- Clear the area around the damage
- Mention any parking restrictions or tricky access
Get a quote
Ring 0345 017 0787, or send us photos through the quote form. With one close-up and one wider picture, we can give you a fixed quote.
Advice
Questions from Perth
Can you quote from pictures?
In nearly every case. We only ask to see it in person if the photos cannot show what we need.
How do I book?
Some pictures, your postcode and how to reach you. On the day, we only need access to the room.
Can a failed resurfacing be redone?
Yes. Stripping the old coating adds time, so it’s reflected in the quote.
Do you work for landlords and businesses?
Yes. We work for landlords, agents, builders and businesses as well as homeowners in Perth.
Do you hold any accreditations?
We hold CHAS, Constructionline, SafeContractor, SMAS Worksafe and Builder’s Profile accreditations.
Will there be fumes?
There is some smell while the coating is applied, which is why we ventilate the bathroom. It clears as the finish cures.
How long does re-enamelling last?
Care for it and it lasts. Avoid abrasive cleaners and suction mats.
What happens if you find more damage?
If we find something the photos didn’t show, we explain it first. The price only changes if you agree.
Repairing versus replacing in Perth
Replacing a bath can take several days across several trades. Resurfacing takes one technician and normally a day, with the bath back in use the next day. Our bath re-enamelling starts from £350. Set against the cost of replacement, a repair is usually a fraction of the price, because nothing has to be taken out, refitted or made good. Your fixed quote shows exactly what’s included.
Why choose Surface Doctor in Perth
- CHAS and Constructionline accredited
- Most jobs done in one visit
- We’ll tell you if it’s not worth repairing
- Work done at your home or business
Take a look at our full price list and guide to resurfacing and replacement costs.
Materials and what they mean for the repair
Roll-top and period baths
Freestanding roll-tops can be done inside and out, with the outside refinished as well.
Pressed steel
Steel baths and trays have a thin metal body under the enamel. Once a chip exposes it, rust follows quickly, so the metal is treated and sealed before the repair.
Looking after it afterwards
After the repair has cured, a few habits help it last:
- Clean with a soft cloth and mild detergent
- Dry the bath after use to stop limescale
- Get any chip repaired quickly
- Repair dripping taps early
Use mild, non-abrasive cleaners, avoid suction bath mats, and keep bottles and razors off the surface.
Rust spots on a worn bath get worse with time, and each one adds to the preparation. It’s simpler to resurface before they spread.
About our accreditations · Every repair comes with a one-year guarantee.
